The process to order tanning bed replacement lamps:
First, you need to know the type of tanning bed bulb you have,
which is
usually a 100 watt,
F71 type with bi-pin connectors on the ends.
The F71 lamp is 69 3/8" long when measured from
metal cap to cap. This is the MOST COMMON home
tanning bed replacement lamp and many different
bulbs
will fit in your bed as long as they are 100 watt!
98% of all home tanning beds are this type:
100 watt, F71, bi-pin
If you know you have the most common 100
watt, F71, bi-pin type lamp...save yourself a lot of
time and money by buying one of our "Home Tanning
Bed Bulb Replacement Kits". Here are the
prepackaged kits to choose from and the starters are
the "choke" type and should be replaced every 3
years or so:
Buy Cheap Tanning Bed
Replacement Lamp Packages here!
16 Real Sun XXX 7.5 UVB 15 Min Max Lamps with Delivery Included:
$225
20 Real Sun XXX 7.5 UVB 15 Min Lamps with Delivery Included:
$275
24 Real Sun XXX 7.5 UVB 15 Min Lamps and 24
Starters with Delivery Included:
$350
Above are the prepackaged kits to choose
from, the starters are the "choke" type and should be replaced every
time your replace your lamps. Select
"Add to Cart" above to go to secure ordering using PayPal.
You
may also have a F72 type lamp
which will have a
black rectangular connector on the end. You
will know the difference between a F71 and F72 when
you identify the socket connector. The F72
type bulb is 69 1/8" long from metal cap to metal
cap. The rare F73 lamp is 70 1/8" long from
cap to cap. Below are the lamps we offer in
these common configurations.
You should replace your starters
every 3
years
or every other lamp replacement. If you
do not know the last time the starters have been
replaced, or if your lamps are slow to fire
completely up, then you need new starters. We
feel so strongly about replacing starters at every
lamp change we include them in the packages you see
above at almost free prices!
Finally,
if you REALLY want to know when to change your lamps,
use a UV Light Meter! That's right, instead of
guessing there is a device which reads in UV light
and gives you an indication of declining or aging lamp
output. When you first buy a new tanning bed
or replace your bulbs, with this device you can measure and record
the meter reading when the lamps are new and
"fresh". Then, over time, you can measure the
lamp output and see how the lamp output has degraded.
Lamp replacement is recommended when the lamp output
is 70% of the original value and we found this to
be around 700 hours on most lamps!
The
cost
is only $145
to know EXACTLY when to change your lamps!
To view our complete
line of tanning bed replacement lamps, please select
from the following links:
Proper seating of tanning bed lamps in their sockets is vital! Poor
seating can lead to poor electrical contact between lamp and socket–and
can significantly shorten the life of any lamp. If the Signature Series
lamps are used in a preheat circuit, it is important to replace the
existing S-12 starter with every or every other lamp change. An old,
worn out $2 starter can dramatically shorten the life of a lamp worth
many dollars more! Minor instabilities such as “snaking” or “swirling”
can be corrected by turning the tanning bulbs on and off several times after installation.
Clean tanning bed replacement lamps can improve UV output by as much as 10%! Therefore, make
sure you wipe your lamps down with a damp cloth on a regular basis
(don’t use solvents!). An tanning bed acrylic that is old and solarized can
filter out over 10% of the UVA that is trying to get through, and over
50% of the UVB that is so vital for a tan! Using your UV meter, check
lamp output with, and then without, the acrylic sheet in place. If the
difference in output exceeds 10%, it’s time to replace the acrylics. It
is always a good idea to have a database on each piece of tanning
equipment you own. When you install the lamps, and after you have burned
them in, read their initial UV output using your UV meter. While
opinions vary widely about when to replace lamps, a generally accepted
range throughout the industry is when the lamp readings drop to about
60-70% if the initial output. Keep separate records for each piece of
tanning equipment, as each lamp type is unique in its output
characteristics.
WEAR PROTECTIVE EYEWEAR; FAILURE TO MAY
RESULT IN SEVERE BURNS OR LONG-TERM INJURY TO THE EYES.
Medications or cosmetics may increase your
sensitivity to the ultraviolet radiation. Consult physician before using
sunlamp if you are using medications or have a history of skin problems
or believe yourself especially sensitive to sunlight. If you do not tan
in the sun, you are unlikely to tan from use of this product.
We offer cheap tanning bed bulbs to all of the following US states and
foreign countries: Alabama, Alaska, Arizona, Arkansas, California,
Canada, Colorado, Connecticut, Delaware, Florida, Georgia, Hawaii, Idaho, Illinois, Indiana,
Iowa, Kansas, Kentucky, Louisiana, Maine, Maryland, Massachusetts, Mexico, Michigan,
Minnesota, Mississippi, Missouri, Montana, Nebraska, Nevada, New Hampshire,
New Jersey, New Mexico, New York, North Carolina, North Dakota, Ohio,
Oklahoma, Oregon, Pennsylvania, Rhode Island, South Carolina, South Dakota,
Tennessee, Texas, Utah, Vermont, Virginia, Washington, West Virginia,
Wisconsin, & Wyoming.
You
may also have a F72 type lamp 
Finally,
if you REALLY want to know when to change your lamps,
use a UV Light Meter! That's right, instead of
guessing there is a device which reads in UV light
and gives you an indication of declining or aging lamp
output. When you first buy a new tanning bed
or replace your bulbs, with this device you can measure and record
the meter reading when the lamps are new and
"fresh". Then, over time, you can measure the
lamp output and see how the lamp output has degraded.
Lamp replacement is recommended when the lamp output
is 70% of the original value and we found this to
be around 700 hours on most lamps! 